Sub-Plate Mounted Valves Leave a Comment / 4 way valves, AS hydraulic cylinder, ASH hydraulic cylinder, ASL hydraulic cylinder, automatic drains, cessna, cylinder accessories, cylinder check, Cylinder Information, dowty hydraulic pumps and motors, dynapower, eaton, float drains, hall 300 series pumps and motors, hall H1500 Pump, hall series 101, hydraulic valves, impluse drains, M and 4 Series Amplifier Air Driven, motor, Neque, neutral lockout switch, packing, packing or seal kit, parker, racine, radiators, reservoir, rexroth, rotary index table, seal kit, series 25 valves that are base mounted, Series 750 Hall pump/motor, series A heat exchanger, Series B Hydraulic Cylinders, series HSS cylinder, series k heat exchanger, series ss cylinders, small bore size cylinders, sundstrand, sundstrand sauer danfoss, swashplate bearing, tie rod end cylinder, torquemotor, Uncategorized, valve in head cylinder, valve manifold, vane pump, Vane Pump Information, vee packing / By Andrew Soper You can get sub plates that have bottom or side ports. On your manifold models. they are used mainly for multiple assembly type units. You can put more than one single unit on it, with different variants and with any amount needed to do the job. They are solenoid controlled and pilot working units. These can be for air or hydraulic use on the bottom/side ports. They are a direct solenoid working unit.Air – 250 PSI/Hydraulic 2000 PSI. You can get sub plates that have bottom or side ports. On your manifold models. they are used mainly for multiple assembly type units. You can put more than one single unit on it, with different variants and with any amount needed to do the job. They are solenoid controlled and pilot working units. These can be for air or hydraulic use on the bottom/side ports. They are a direct solenoid working unit. Air 250 PSI/Hydraulic 2000 PSI. You can get sub plates that have bottom or side ports. On your manifold models. they are used mainly for multiple assembly type units. You can put more than one single unit on it, with different variants and with any amount needed to do the job. They are solenoid controlled and pilot working units. Single Sub Plates – 3/8″ 1/4″ ports….new #10-1116 old #BMJ-53 3/8″ ports…new #10-1115 old #BMJ-28 Old #BMJ-54 can no longer get New #10-0289 Old # BMJ-85…………………..this is for Air This is for Hydraulic New #10-0291 Old #BMJ-87 New #10-0293 Old #BMJ-89 Stacking manifolds…….if you order your valves and sub-plates together, they are put together at the factory. Valve sizes These valves have the same length, it is just different in how wide it is and how tall it is. It is an interchangeable manual, mechanical and pilot actuators. Air is 250 PSI and Hydraulic 2000 PSI. The clevis model is made to hook up linkages for the remote control/sensing units. It comes 2/3 way detents and spring return/spring centered. Valve sizes – these valves have the same length, it is just different in how wide it is and how tall it is. It is an interchangeable manual, mechanical and pilot actuators. Air is 250 PSI and Hydraulic 2000 PSI. If you need a sub-plate that is put on a valve, then look on these charts for the sizes on new units. Air PSI-250/Hydraulic-2000 PSI and 1/4″ Goes right into the port – 1000 PSI The picture at the top is #10-0333. These are for 1/4″ & 3/8″ air/hydraulic valves. The picture on the bottom shows that the solenoid mount plate is for BMJE units. All the other sub plates use 1/4″ flat valves on the top & bottom. Call us about any kind of valves you may have, call us at 662-871-8403tupelohydraulics@gmail.com